Jaxxon 1335 Clear Epoxy Binder

Product Notes

• Jaxxon 1335 can be used as the binder in grouts, slurries and mortars with he addition of stir-in sand, fillers and powders.
• Jaxxon 1335 can be used as clear, thin-film rollcoat coat, however it should not be used in applications requiring resistance to rapid changes in temperature during service and/or cleaning (i.e. thermal shock).
• Should not be applied in temperatures lower than 5°C.
• Consistent with all epoxies, Jaxxon 1335 will tend to discolour upon extended UV exposure. Over-coat with Ezypoly (PU topcoat) if required.
• If more than one kit is mixed at a time, the product can reach dangerously high temperatures and experience a significantly reduced pot life.
• Clean up with MEK, acetone or methylated spirits.

Surface Preparation

Concrete:

New concrete surfaces should be allowed to cure for a minimum of 28 days. Contaminated concrete surfaces should be degreased with an appropriate detergent. Diamond grind, shot blast, scarify or scabble as required to obtain a suitable surface profile for the coating system to be applied. Ensure surface is clean, dry and dust-free again if there’s a delay before application. Properly prepared surfaces should be structurally sound (minimum of 25MPa compressive strength/1.5MPa tensile strength) and free of contamination, laitance and any loose material. 

Coated Surfaces: 

Maximum delay between coats is 45 hours @ 25°C. Should this time be exceeded the previous coat must be lightly abraded with 80-120 grit paper, vacuumed and wiped with methylated spirits or other suitable solvent. Old, existing films can be over-coated providing they’re in good condition and there are no adhesion issues. If in doubt, a tensile adhesion test should be conducted.

Mixing

For full safety instructions, consult SDS. Wear protective clothing, goggles and gloves to prevent skin and eye contact.

NOTE: Check packaging for correct components before mixing.

Mix product at a ratio of 5:3 by volume. Pour Part B into Part A and blend for 2 minutes.

Jaxxon 1335 kits can be split by using the following weights and volumes to make 1 litre -

Part A	Part B
710g/640mL	380g/360mL

If pigmenting, pre-mix pigment pots into Part A first with a drill mixer before adding Part B. 

When mixing mortars or levelling compounds, gradually add filler/aggregates last while continuing to mix, scraping sides with a flat spatula to ensure all product is taken in. Keep mixing until a consistent appearance is obtained.

Application

Brush, roller, squeegee or trowel. Technique and coverages will depend on the type of product being used and its application.

Rolling (Primers/Sealers/Clear Coatings): 

Pour product immediately onto the floor after mixing. Start 50cm from a wall and work towards the exit point pouring in an “S” shaped pattern.

Leave enough mixed product to cut in with a brush next to vertical surfaces and around tight areas. Approximately 100mm is typical.

Perform a rough spread using the squeegee to achieve a relatively even film, allow product to level for 2-3 minutes, then backroll smooth using de-linted roller covers.

Roll in long, even, overlapping strokes to get the product feeling and sounding the same. 

Trowelling (Levellers/Patching Compounds/Coves): 

Prime cleaned surfaces first if required. Position mixed product over the freshly primed areas using appropriate spreading techniques and trowel to a smooth finish as required.

Products must be applied within the pot life times listed in the Cure Schedule table to ensure best results.

Storage

Keep containers closed when not in use. Store below 40°C. Do not store in direct sunlight. Shelf life is at least 12 months in original, unopened container. Seek advice from your local council regarding accepted disposal methods.

First Aid

CAUTION: KEEP OUT OF REACH OF CHILDREN.  IF ON SKIN: Remove immediately all contaminated clothing. Rinse skin with water. IF IN EYES: Rinse cautiously with water for several minutes. Immediately call a POISON CENTRE (Australia - 13 11 26) or doctor/physician. If skin irritation occurs: Get medical advice/attention. 

WARRANTY DISCLAIMER: The technical data given herein has been compiled for your help and guidance and is based upon our experience and knowledge. However as we have no control over the use to which this information is put, no warranty express or implied is intended or given. We assume no responsibility whatsoever for coverage, performance or damages, including injuries resulting from use of this information or of products recommended herein.